If you’ve ever experienced a gas stove igniter that keeps clicking, you know how frustrating it can be. Not only is the clicking sound annoying, but it can also be an indication of a more serious issue.
So, let’s explore some common reasons why a gas stove igniter keeps clicking and how you can troubleshoot the issue. And if you find the need for a professional Viking stove repair, we will also share valuable information about a trusted service provider.
5 Common Reasons Why a Gas Stove Igniter Keeps Clicking
If you notice that your gas stove igniter keeps clicking, the following could be the potential reasons:
- Dirty or Wet Igniter
One possible reason for continuous clicking is a dirty or wet igniter. When dirt or moisture is on the igniter, it can cause the electrical current to arc, resulting in continuous clicking.
Troubleshooting step:
- Turn off the stove and wait for it to cool down.
- Once it has cooled, locate the igniter and inspect it for any signs of dirt or moisture.
- If you see any debris or moisture, use a dry cloth or brush to clean the igniter.
- Avoid using water or any liquid cleaning agents, as they can damage the igniter.
- After cleaning the igniter, turn on the stove and observe if the clicking sound persists.
If there are still clicking sounds, there may be other underlying causes for the issue.
To prevent this issue from happening again, make sure to keep the stove and the igniter clean and dry. After cooking, wipe down the stove with a dry cloth and make sure to remove any spills or food debris around the igniter.
Additionally, avoid using excess water when cleaning the stove, as it can cause moisture to get into the igniter.
- Broken Igniter Switch
A broken igniter switch is another common reason why a gas stove igniter may keep clicking.
The igniter switch sends an electrical signal to the spark module to create a spark that lights the burner. If the switch is broken, it can cause the spark to continue even when the burner is turned off, resulting in continuous clicking.
Troubleshooting step:
- Turn off the stove and wait for it to cool down.
- Once cool, find the igniter switch and inspect it for any signs of damage.
- If the switch is visibly damaged or worn, it may need to be replaced.
- If the switch is in good condition, use a multimeter to test the switch’s continuity.
- Set your multimeter to “ohms” and touch its probes to the switch’s terminals. If the multimeter reads “zero,” the switch is closed and functioning properly. If the multimeter reads “infinite,” the switch is open and needs to be replaced.
If the igniter switch needs to be replaced, it’s important to call an expert Viking stove repairman to get a replacement switch compatible with your stove’s make and model. They have access to genuine stove replacement parts.
- Loose Igniter Connections
Another potential reason why a gas stove igniter may keep clicking is due to loose igniter connections. Over time, the igniter connections can become loose or corroded, preventing the igniter from working properly.
Troubleshooting step:
- Be sure that the stove is turned off and has cooled down completely.
- Next, locate the igniter connections on the burner assembly.
- Check to see if any of the connections are loose or corroded.
- If the connections are loose, tighten them using a pair of pliers or a wrench.
- If the connections are corroded, use a wire brush or sandpaper to clean them.
- Once the connections have been tightened and/or cleaned, turn the stove on and see if the clicking has stopped.
If the clicking persists, it may be necessary to replace the igniter. While you can attempt to replace the igniter yourself, getting a professional to do the job will be more practical. A professional Viking stove ignitor replacement will ensure an authentic replacement part.
- Faulty Spark Module
A faulty spark module could also be why a gas stove igniter keeps clicking. The spark module is responsible for creating the spark that ignites the burner, and if it malfunctions, it can cause the igniter to continue clicking.
Troubleshooting step:
- Be sure the stove is turned off and has cooled down completely.
- Next, find the spark module, usually located at the back of the stove, behind the control panel.
- Inspect the spark module for any damage or wear, such as burn marks or cracked wires.
- If the spark module appears to be in good condition, use a multimeter to test it for continuity.
- Set your multimeter “ohms” and touch the probes to the module’s terminals. If the multimeter reads “zero,” it means that the module is functioning properly. If the multimeter reads “infinite,” it means the module is faulty and must be replaced.
If the spark module needs to be replaced, you can consult the stove’s manual or contact the manufacturer to ensure you purchase the correct part. If you’re unsure about attempting the replacement, look for a certified Viking stove repair near me.
- Broken Igniter
A broken igniter itself could be the culprit for a gas stove igniter that keeps clicking. Over time, the igniter can become worn or damaged, preventing it from creating the spark needed to ignite the burner.
Troubleshooting step:
- Be sure the stove is turned off and has cooled down completely.
- Then, locate the igniter, which is usually located near the burner.
- Inspect the igniter for signs of damage and wear, such as cracks or chips.
- If the igniter appears to be in good condition, test its continuity using a multimeter.
- Set your multimeter to “ohms” and touch the probes to the igniter’s terminals. If the multimeter reads “zero,” it means that the igniter is functioning properly. If the multimeter reads “infinite,” the igniter is broken and needs a repair or replacement.
If you don’t know how to fix stove igniter, then the best thing to do is call a professional. They can perform the needed repairs and can provide the needed replacement if the igniter renders irreparable.
Professional Viking Stove Repair
Gas stove igniter issues, such as clicking noises, can be frustrating and hinder productivity. So, it’s best that you address them right away so you can go back to preparing scrumptious meals for your family.
While the above steps are great for DIY troubleshooting and repair, attempting repairs yourself are highly discouraged. The best way to address igniter issues still is a professional service.
If you’re looking for a trusted provider to service your stove, Viking Appliance Repairs is here. We are a certified Viking repair and maintenance provider that can address any issues in Viking stoves.
So, hurry and book your service with us! Don’t let a broken stove igniter stop you from being productive. Schedule your appointment by calling us at (855) 393-3634.